Found a fix for my joy-con wiggle. There is a plastic section on the bottom that doesnt have any screws or locks where the tape can sit.
He had pulled too hard on one.
How to fix joycon railing. These screws are torqued down and can be difficult to remove. One of the popular methods that been used to get the system in RCM is by using a paper clip aluminum foil or a 3D printed jig. Until Joycon rail replacements become as readily available as the locks themselves Id hold off on swapping them out for metal.
The Nintendo Switch controller is an awesome technical achievement unfortunately some of the most important parts of the controller are made of plastic and. The battery in the left Joy-Con is now removed. For the right Joy-Con hold it upright with the Button positioned upward and the Joy-Con strap in the other.
Now grasp the battery and remove it from the controller. The plastic locking latch in the sliding rail of your Joycon is chipped or deformed and needs to be replaced in the linked photo the blue Joycons latch is damaged and the red ones. To do this hold down the off button for a few seconds then select the Power Options sub-heading and confirm by selecting off.
Headquarters are in Redmond Washington. It had some minor water damage its stuck on the attach joycon screen so cannot test further. Make sure youre using a JIS screwdrivernot a Phillips screwdriverduring this procedure.
Use a JIS 000 screwdriver to remove the four 37 mm screws securing the left Joy Con rail to the frame of the device. Its the right joycon not being detected in my case it doesnt charge either. All you have to do is superglue that plastic rail to the front plate and the back plate of course this fix will prevent any future disassembly but now i can sleep good at night knowing that my joycons doesnt wobble or creak anymore.
The rails are a bit more troublesome to replace though which might be an issue for those who already feel unsure about opening up the Joycon. Realized it wasnt an issue with my Switch unit itself when the joy-con was wiggling in the grip as well. Either way one of them will get the job done I myself have failed victim to damaging the right joy con rail connectors with a faulty jig.
Look in the railing if something is blocking the notch in. Insert the nylon spudger between the console and the battery and carefully lever it up to disconnect the battery. Joycon slides off of the main console body on its own or with very light force without pressing and holding the release button at the back.
This form is only available to those that live in the USA or. Nintendo of America Inc. Nintendo Switch LetsFixNEW UPDATED VIDEO.
Otherwise you risk stripping the screws. If you have five or more Joy-Con that need repair please contact us by phone at 1 800 255-3700. Make sure youre using a JIS screwdrivernot a Phillips screwdriverduring this procedure.
Did either of you manage to fix this. You can order one for 4 and change it out yourself if you have the right. Use a JIS 000 screwdriver to remove the four 37 mm screws securing the right Joy Con rail to the frame of the device.
Part for this repair. New rail new connector lots of IPA but nothing. My right joycon wont connect handheld but will wirelessly and it charges on the switch Im desperate for solutions but I dont want to buy a new joycon.
Placed tape on the top and bottom portions of the joy-cons rail next to the SL and SR buttons. Try to clean the botton of the rail with a toothbrush. Only apply a little at first just enough to create some friction with the console.
These screws are torqued down and can be difficult to remove. Ok so I got this problem. They are located on the bottom of the plastic piece where the joy-con would slide into the rail socket and the bottom of the rail.
Httpsyoutube1oj-MNj6kOERecently one of my students came to me with an issue. If the and – symbols are not aligned and the Joy-Con strap is incorrectly attached. Took three layers of tape to stop the wiggling.
Before proceeding to replace the left Joy Con rail of your Nintendo Switch you must for evident safety reasons turn off your device. Its broken where the fold is. Simply apply a small square of electrical tape to the bottom of the entry rail on the console.
Theres a flexible ribbon cable along the rail that is folded within the plastic shell.